|
PACET’S PROFAN KITS
& FMS ASSEMBLIES
A further development of the Thinline & HighProfile range, where
maximum performance is required and there is sufficient space for the bigger motor, with
dedicated Pull or Blow blades. These
kits have proved very popular particularly with competition customers or those requiring
the very best performance. Either
supplied as Fan/Motor/Shroud (FMS) assemblies or as complete kits. The FMS assemblies are
available for those who wish to make up their own assembly or replace the existing unit.
Delete the prefix K from the part number when ordering the Profan FMS Assembly only.
Water resistant motors can be submerged for 3 to 4 hours are
available on Profan models only - add /WR to part number when ordering. WR motors add 10mm to H measurement.
All components available separately – see Spares Page for details.
Thinline Profans
|
* |
W
mm |
D
mm |
P
mm |
H
mm |
S
mm |
CFM
** |
m³/h
** |
Amps |
KPF0811 |
8” |
214 |
241 |
238 |
89 |
35 |
498 |
846 |
7.80 |
KPF0911 |
9” |
243 |
276 |
279 |
89 |
35 |
908 |
1543 |
8.90 |
KPF1011 |
10” |
269 |
301 |
323 |
89 |
35 |
1090 |
1852 |
10.70 |
KPF1111 |
11” |
295 |
324 |
324 |
89 |
35 |
1242 |
2110 |
10.90 |
KPF1211 |
12” |
321 |
333 |
335 |
96 |
35 |
1640 |
2834 |
12.00 |
KPF1311 |
13” |
346 |
353 |
354 |
100 |
35 |
1980 |
3364 |
12.19 |
KPF1411 |
14” |
367 |
373 |
374 |
100 |
35 |
2139 |
3634 |
12.29 |
KPF1611 |
16” |
406 |
418 |
418 |
100 |
35 |
2354 |
3999 |
14.00 |
* Nominal blade size – see W, D, P*, H & S
for overall dimensions
** Performance - At 0.15” ( 3.75mm) static pressure is the equivalent of a
typical 1.5” (39mm) thick radiator. Free air figures are always much
greater and look more impressive but are not often relevant and therefore not shown here. Performance figures, intended as a guide, are shown for
pulling mode, the most reliable. Blowing
performance is unreliable, as it has degrees of spill and wastage and is only used when
space is tight. ‘0’ Amp draw
is taken at nominal 12V rating. Normal
test voltage is 13.5V, for 24V amp draw figure a typical reduction of 45% should be
applied.
-
add P for Pull or B for Blow after part no. e.g. KPF1011P
- add /24 to part number when ordering 24V
- for Twin Kits add /TW to part number, e.g.KPF1011/TW. See Twin Kits for details
High Profile
Profans
|
* |
W
mm |
D
mm |
H
mm |
S
mm |
CFM
** |
m³/h
** |
Amps |
KPF107
|
10” |
267 |
282 |
96 |
56 |
980 |
1665 |
9.00 |
KPF115 |
11.5” |
305 |
305 |
105 |
60 |
1690 |
2871 |
12.09 |
KPF126 |
12” |
333 |
356 |
105 |
60 |
2150 |
3653 |
13.09 |
KPF127 |
12” |
318 |
330 |
105 |
56 |
2360 |
4009 |
14.10 |
- add P for Pull or B for
Blow after part no. e.g. KPF1011P
- add /24 to part number when ordering 24V
- for Twin Kits add /TW to part number, e.g.KPF1011/TW. See Twin Kits for details
Twin
Kits
Twin kits include the same components as single kits, with one
thermostat and one override switch.
Where X and L are dependant on fan size and specification
All the kit components are available separately - click here for details
|
